Astex Professional Astex-Term thermal insulation system Facade plasters in the thermal insulation system Mineral plasters
KRATZPUTZ CYCLINE facade plaster
CYCLINE KRATZPUTZ plaster is intended for use as decorative facade plaster.
- With a 4-10 mm or 10-16 mm fraction
- Frost and waterproof
- Resistant to mechanical damage
- Vapor permeable
Calculate expenditure
Expenditure
with 4-10 mm grain thickness: 35 kg per m2 with a grain thickness of 10-16 mm 45 kg per 1m²
Shell life
12 months from the date of production
Packaging
50kg
Reference document
European Technical Assessment 17/0726
Properties
CYCLINE KRATZPUTZ plaster is factory mixed, dry, mineral mortar, which after mixing with water is ready for use. It is suitable for manual application. Plaster is plastic and easy to apply and process. When used correctly, it can be applied in single layers of 10 to 16 mm thick. Hardened plaster CYCLINE KRATZPUTZ is hydrophobic and permeable to water vapor as well as resistant to water, weather conditions and frost.
Application
CYCLINE KRATZPUTZ is intended for use as decorative facade plaster. It can be applied to the surface plastered with masonry plaster.
Substrate preparation
The plaster base must be load-bearing and free of substances that weaken plaster adhesion (e.g. release agents, sandy plaster fragments, dust, efflorescence, dirt). The plaster base can be dry or moist, but it cannot show moisture pressure. Old and damaged plasters, paint layers and other coatings should be carefully removed. The masonry plaster surface should be scratched before it dries and should resemble a grid.
Application method
Pour in the right amount of CYCLINE KRATZPUTZ mortar in relation to the size of the concrete mixer and work until it reaches the right, homogeneous consistency. Usability lifespan after mixing: approx. 1 hour - depending on the ambient conditions. After obtaining the right consistency CYCLINE KRATZPUTZ is applied with a masonry trowel. The applied mortar is smoothed with a stainless steel trowel to the thickness of the aggregate. The applied layer of plaster should be scraped (scratched) with a notched trowel. At the right moment (the aggregate grains must pop out) the surface should be uniformly gouged. By sweeping the scraped surfaces, subsequent flaking can be minimized. To avoid traces of joining, always work fresh on fresh. Solid mortar must not be made again by adding water or fresh mortar! Do not use at temperatures below + 5 ° C. The time instructions given relate to the normal temperature range + 20 ° C and relative humidity around 65%. Lower temperatures lengthen, higher temperatures reduce the usability lifespan and hardening time. The CYCLINE KRATZPUTZ plaster should be protected against too fast evaporation of water, especially against sunlight and wind. If the temperature remains high after application, the KRATZPUTZ CYCLINE should be bedewed with water to aid the setting process. Contraction scratches do not matter and are not considered defects because they do not affect the technical value of the plaster. Do not use on gypsum substrates.
Expenditure
With a grain size of 4-10mm, approx. 35 kg per sqm. With a grain size of 10-16 mm, approx. 45 kg per m2.
Storage and transport
The plaster should be transported and stored in tightly sealed bags, in dry conditions (preferably on pallets). Protect from moisture. The shelf life is 12 months from the date of manufacture on the packaging.
Caution
ASTEX- PUCZYŃSCY PLASTERS PAINTS guarantees and bears responsibility for the quality of the product, but has no influence and is not responsible for the manner of use and conditions in which it was used. The recommendations and scope of use of the product or method of performance does not release the contractor from carrying out work in accordance with the principles of building art and health and safety regulations. If in doubt as to the use of the product, please contact us at Tel. 0 54 283 21 24 or by e-mail to the address: laboratory@astex-tynki.pl
Do you have questions? Doubts? Ask an advisor Contact form
